Have a 350 chev small block, bought a new mini starter. This also aides in helping the starter not to move.
As far as i know you are supposed to shim starter motors on small block chevy's, but only small thin shims not 10mm.
Small block chevy starter shims. Chevy small block v8, chevy big block v8, natural. If the clearance is too small, add one shim at a time between the starter and engine block to bring it into specifications. Chevy small block & big block v8 starter shim & bolt kit ;
Bolt the starter motor back onto the engine block. The secret is the bolts. Loosen the two allen bolts and move the solenoid toward the.
I use these starters on all 383 engine builds and have never had one that fits without rotating the body. Grinding (but more often the removal of a shim or some material on the starter mount pad, will stop grinding). Not long ago i replaced the starter on my small block.
If you are changing the starter i would not shim it right away.shims are used only when the starter sounds tight. All big blocks should use a starter brace. Ultimate starter problem ray, the power master starter is a very good starter, however if you do not clock it right the body of the starter will make contact with the block before the bolts actually get tight.
If you have a 168 tooth flywheel and a staggered bolt pattern block, this swap will also work on any chevy small block or even a 4.3 v6. I put shims inside and outside, both sides, and could not get it to line up right. Chevy small block & big block v8 starter shim & bolt kit ;
Not sure what engine came in different overfinch rr's but i know older gen one. I have been searching through the posts and found the best answer was to get a brand new, not remanufactured, starter. Starter braces mount to the rear of the starter and bolt to the block.
Skip to the end of the images gallery. Gt01gt ️ (23,313) 98.6%, location: (hard job with headers and no lift!) my previous starter came out with a pretty big shim.
4.7 out of 5 stars 22. Shims are really good for drives that get hungup (insufficent distance between drive and fw). .0075, moving the starter down and out, away from the flywheel.
Skip to the beginning of the images gallery. 89rs w/a 400, some aluminum things, a tremec and 9inch w/a 4.10 gear idle.mpg. Shave weight off your car with this super light 7.5 pound starter which is an astounding 12 pounds lighter than a stock starter;
However, i`ve learned on small blocks with 10:1 compression and lower is fine without the brace, if compression is over that mark it needs one. Shim as required at minimum clearance location. Chevrolet chevy mini starter bolt and shim kit.
Test with the paper clip again, and if the paper clip still doesn't fit, repeat the process and add another shim. Proper shimming to increase clearance (fig.a) use entire shim across both holes (fig.3).015 shim increases clearance approx. .0075, moving the starter down and out, away from the flywheel.
.010 the starter drive tells the story: You could have the wrong starter nose cone, or if you are using shims, remove as many as it takes to get the proper clearance. I put shims inside and outside, both sides, and could not get it to line up right.
If the starter skips as it is turning the engine, your starter could be too far from the flexplate/flywheel. Have a 350 chev small block, bought a new mini starter. Do this until the paper clip fits in between the gaps.
(use no more than 4 shims) to decrease clearance (fig.b) use 1/2 shim only on the outer mounting The valley of the starter pinion to the tip of the ring gear tooth.( #1 standard paper clip is usually about 0.035” in diameter and makes an easy tool.) check clearance at least three places on the ring gear. Chevy small block & big block v8 starter shim & bolt kit ;
4.7 out of 5 stars 22. 2 long bolts for 168, one long one short is 153. Even on small blocks that don`t.
Chevy mini starter shim & bolt set. I have been searching through the posts and found the best answer was to get a brand new, not remanufactured, starter. Small block chevy mini starter bolts.
Grinding (but more often the removal of a shim or some material on the starter mount pad, will stop grinding). When i got the new starter, it came with instructions and several different shims. Find chevrolet 5.7l/350 chevy small block gen i starter shim kits and get free shipping on orders over $99 at summit racing!
Jegs 10016 Oe-style Mini Starter Small Blockbig Block Chevy 168 Tooth Staggered Mounting Configuration 51 Gear Reduction 1001 Compression Ratio 18 Hp 14 Kw 8 Lbs Natural Finish Sold Individually – Jegs High Performance