You don’t want the hot tub’s heater or pump to work while the water level is low. Turn the power to the spa off at the circuit breaker.
Ideally, you’d use a pump for this, but if it doesn’t work or if you want to do it without it, here is how it can be done with a hose.
How to drain a hot tub with a pump. How to drain a hot tub without a pump. Turn off the hot tub and pull the drain plug outward. Turn off the hot tub.
They are also useful for many household tasks that require transferring water from one place to another. You don’t want the pumps or jets to run while there isn’t any water in the spa. Most hot tubs have a draining hole, and some of them even have a threaded portion to add a spigot and a hose.
When the hot tub is empty, turn the sump pump off and detach the hose. It used to take about 10 minutes to drain all of the water out using this method. Personally, i like using the aquapro apc3000 submersible pump.
Use the hot tub drain valve. Pump hose, filter hose and the main pipe that distributes all the water. The fastest way to drain a hot tub is to use a submersible pump.
After identifying where the crack is, drill two small holes on either end of it. This 1/3 hp pump can be used with a ¾” garden hose or a 1¾“ sump pump discharge hose to remove up to 30 gallons per minute (1,800 gallons per hour). Most hot tubs have a drain valve (sometimes called a spigot, drain plug or spa drain) which you can utilize to empty it.
Draining a hot tub through the drain valve can take up to 2 hours. The fastest way to drain a hot tub is by using a submersible pump (found online and in hardware stores). You can now disconnect the hose from the faucet bib.
You just need to connect a hose, drop the pump into the hot tub and switch it on. Next, find your drainage spigot. Remove and clean the filter, and gather all the supplies, then you can start draining your hot tub.
Turn the power to the spa off at the circuit breaker. Depending on the model, a hot tub usually comes with primary and auxiliary spigots. Drain the spa using either a submersible pump or a hose attached to the drain plug at the base of the hot tub.
You can hook up a ¾” spigot onto this drain, attach it to a hose, and let the water drain downhill through it. Removing unwanted water from construction sites, flat roofs, patios, lawns, washing machines, dishwashers. You need to turn off all hot tub functions and switch it off on your circuit breaker;
Turn off the power to the tub. These usually can be connected to a much thicker hose than a standard garden hose and will pump out the water very fast. Turn on the pump and drain the water;
Be certain to hold the kink in the hose until you get the end that you are holding below the level of the hot tub itself. There are three most important places in a hot tub that need to be protected during winterizing: To drain using the spigot:
Disconnect and clean the pump. Depending on the size of your spa, it should take around an hour to drain using the hot tub’s drainage spigot, or ten minutes to drain with a submersible pump. You don't want the pumps or jets to run while there isn't any water in the spa.
If the spigot is situated right over a drain, let the water flows out through it by opening the valve. Or you can use a submersible pump which takes about 15 minutes.****. Preventing flooded basements during a power outage.
Do this a couple of feet below where the connection to your hose bib is. The timing of the draining intervals depends on the number of users in the hot tub every day and may be as often as every two weeks for commercial settings or as little as every 75 days for a single user. If you’ve already tried draining a hot tub by connecting a hose to the drain and waiting for the water to clear out, you will be delighted with a drain pump solution.
Drain pumps drain the water by dewatering the hot tub leaving only a few inches of water in minutes, not hours. The drill bit should be slightly larger than the crack itself. Hot tub professionals use submersible pumps to quickly drain spas when they are in need.
How to drain a hot tub with a submersible pump. 4.3 out of 5 stars. Pump marvel is more than a pump to empty the hot tub.
Open the ball valve on your spigot so the water can drain. This is to keep the water sealed inside the hose for the time being. This will make your task easier.
You can drain your hot tub with a standard garden hose, which can take 2 hours or longer. Fluentpower submersible pump 3/4hp 3300gph, oil chamber seal structure, drain clean/dirty water from garden,pond,pool,hot tub,flooded cellar, with float switch and hose connector. With this kind of tub, you will use the primary spigot to drain it slowly.
The easiest way to drain a hot tub is using its draining spigot. * first and most important make sure that your hot tub is unplugged and wait for the water to cool off. Safely removing all the water from pool covers.
This will prevent the crack from spreading further. If you don’t have the time to wait, then consider using.